Skip to content
Formulaxis
Preliminary sizing guide

Choose pipe diameter without guessing coefficients

A 12 m³/h example: why 40 and 50 mm inside diameters have very different losses.

Formulaxis · Documented technical demonstration · Revision: 15 November 2026

Short answer. Sizing a pipe is not about choosing an arbitrary nominal diameter. At fixed flow, actual inside diameter determines velocity, then Reynolds number and roughness determine the Darcy factor. Straight-pipe and local losses must then be assessed against pressure and the pump curve.

Here we want to convey 12 m³/h of water at 20 °C over 60 m through new commercial pipe. The teaching aim is to compare three actual inside diameters, not three nominal DN sizes. The calculation describes turbulent flow in straight pipe; it does not by itself size a complete system.

1. Find data instead of guessing

InputValue usedJustification and pitfall
Flow rate Q12 m³/hExercise process requirement; pump power alone cannot determine it.
Inside D40, 50, 63 mmScenario dimensions that are internal , not standardized DN sizes. Check actual wall thickness/schedule.
Water at 20 °Cρ = 998.16 kg/m³; μ = 1.0016 mPa·sDensity: Hydraulic Institute; reference viscosity: ISO/TR 3666.
New commercial steelε = 0.045 mmBentley roughness example; aging/deposits not represented.
Straight length60 mMeasured along the route; excludes bends and valves.
Q = 12 m³/h · L = 60 mCompare inside D = 40, 50 or 63 mm at identical flow
Our comparison keeps flow and length identical. Diameters are illustrative internal dimensions.

Water and roughness data are retained in the fluid and pipe properties table, with links to the original sources.

2. The five calculation steps

1 Convert flow and calculate velocity

12 m³/h = 0.003333 m³/s. For D = 40 mm, internal area is πD²/4 and velocity approximately 2.65 m/s. Do not use outside diameter or a DN label alone to calculate area: wall thickness actually changes velocity.

v = 4Q / (πD²) = 2.653 m/s (inside D 40 mm)
Same Q = 12 m³/hD 402.65 m/sD 501.7 m/s
Velocity comparison · original Formulaxis diagram, values for this example only

2 Determine the regime using Reynolds number

Viscosity depends on temperature and fluid type. For this water example: Re = ρvD/μ ≈ 105 739 at 40 mm diameter. Flow is turbulent, allowing the explicit relationship selected below. Recalculate for another fluid, temperature or transitional regime.

Re = ρ × v × D / μ
D and velocity with fluid at 20 °Cρ998.16 kg/m³μ1.0016 mPa·sRe D 40≈ 105 739
Determine Reynolds · original Formulaxis diagram, values for this example only

3 Choose roughness with its source

A value of 0.045 mm can serve as anassumption for new commercial steel. It does not automatically apply to drawn stainless steel, polymer or old scaled pipe. ε/D is needed for turbulent calculations. A material data sheet without internal surface condition is insufficient for a detailed study.

Same liquid, two different wallsNew steelε 0.045 mmGalvanized steelε 0.15 mmAged pipeMust be characterized
Roughness is a surface property · original Formulaxis diagram, values for this example only

4 Calculate straight-pipe losses

We use the explicit Swamee–Jain formula to approximate the turbulent Darcy factor, then Darcy–Weisbach. This is the Darcy factor, not the Fanning factor (a factor of 4 difference). Both diameters are thus compared using the same model and fluid properties.

f = 0.25 / [log₁₀(ε/(3.7D) + 5.74/Re^0.9)]² ; Δp = f × (L/D) × ρv²/2
Straight-pipe Δp over 60 mD 40119.3 kPaD 5038.6 kPa
Loss comparison · original Formulaxis diagram, values for this example only

5 Add local losses and static head

A real network includes bends, valves, strainers, check valves, section changes and sometimes elevation head. Each item needs a documented K, not a generic count of bends. Add head losses and static head to construct the system curve for comparison with the pump curve; fitting K values vary with product and Reynolds number.

Δp_sing = ΣK × ρv²/2 ; H_total = H_géo + (Δp_rég + Δp_sing)/(ρg)
Straight-pipe loss is not enoughPipeDarcy ΔpFittingsΣK · ρv²/2Elevation differenceρgΔz
Constructing the system curve · original Formulaxis diagram, values for this example only

3. Numerical example: 40 or 50 mm inside diameter?

At 12 m³/h over 60 m, with identical water and roughness, increasing from 40 to 50 mm reduces straight-pipe loss by about 119.3 → 38.6 kPa. This is not a general rule for changing DN: it follows from the internal diameters in our scenario.

Inside Dv (m/s)ReDarcy fStraight-pipe Δp (kPa)H (m)
40 mm2.65105 7390.02266119.312.19
50 mm1.7084 5910.0223738.63.95
63 mm1.0767 1360.0223612.21.24
Provisional decision: a larger pipe reduces straight-pipe pressure loss at fixed flow, but costs more and eliminates neither local losses nor pressure, minimum-velocity or operating constraints. Final selection must include pumping cost and network requirements.

Try another diameter and flow rate

Water at 20 °C, ε = 0.045 mm (new commercial steel), same turbulent model; automatic rejection outside the Swamee–Jain range.

2.65 m/sMean velocity
105 739Reynolds
119.3 kPaStraight-pipe pressure loss
12.19 mStraight-pipe head loss

4. Common pipe-calculation errors

DN 50 does not mean inside D = 50 mm

DN is a nominal designation, not necessarily actual diameter. For a pipe, determine outside diameter and wall thickness (or schedule), then calculate the flow diameter. The difference enters the area quadratically and strongly affects losses.

Using “standard” roughness for an old line

Scale, corrosion or welds can change the internal condition. For a pipe in service for years, comparing several plausible roughness values is more useful than quoting 0.045 mm to six decimal places.

Ignoring fittings can hide the real problem

A partly closed valve or clogged filter can dominate losses even if the straight pipe is correctly sized. Check equipment positions and manufacturer curves or K values, especially in compact networks with many fittings.

This guide does not cover NPSH/cavitation, hydraulic transients, water hammer, erosion/corrosion risk, pressure resistance or pump curves. Straight-pipe loss alone cannot validate an installation.

5. Workflow through existing calculators

Related tables: water and roughness with Bentley / Hydraulic Institute / ISO sources. Calculating local losses requires the actual fitting type, not a fictitious “standard” ΣK value.

Sources and data status

Numerical values are retained in this document even if URLs change. The tables are reconstructed selections with source attribution, not full copies of brochures. Formulaxis calculations and teaching assumptions are identified separately.

  1. Hydraulic Institute — water propertiesWater density at 20 and 40 °C.
  2. ISO/TR 3666 — water viscosity (reference)Dynamic viscosity of water at 20 °C; explanatory extract consulted.
  3. Bentley OpenFlows — Darcy–Weisbach roughnessApproximate roughness values for new pipes; no universal value.
  4. ASHRAE — Pipe Design / local lossesFitting K values vary with geometry and flow regime.

Sources consulted / results cross-checked on 15 November 2026. Data sheets and catalogues may be revised: check the current edition for a real project.