FORMULAXIS
All calculators
Browse tools by field or search for a quantity, formula or topic.
FORMULAXIS
All calculators
91 calculators
Toolbox
3D cross product: calculating components, magnitude and areas
Calculate the cross product of two 3D vectors, its magnitude and the areas of the parallelogram and triangle. Examples, factor order and a right-handed coordinate system.
Toolbox
Analytic geometry: calculate distance, midpoint and line
Calculate the distance between two points, the midpoint and the equation of the line in 2D. Examples, vertical lines and coincident points, coordinate-system conventions.
Power transmission and gears
Angular momentum: calculation about a fixed axis
Calculate angular momentum, angular velocity or inertia about a fixed principal axis. Signed examples, units and conservation conditions.
Strength of materials and structural sizing
Bar: calculating axial stress and elongation
Calculate axial stress, strain and elongation of a uniform bar in tension or compression. Conversions, examples and elastic limits.
Strength of materials and structural sizing
Beam deflection: calculation for three load cases
Calculate maximum deflection: two supports with a central force or uniform load, or a cantilever with an end force. Formulas, units and worked examples.
Bearings, shafts and joints
Bearing: calculate basic rating life L10
Calculate the basic rating life L10 of a ball or roller bearing in millions of revolutions and hours. Constant speed, examples and statistical interpretation.
Bearings, shafts and joints
Bearing: calculating the static safety factor C₀/P₀
Calculate a bearing’s static safety factor from its static load rating C₀ and equivalent load P₀. Examples and comparison with the selected criterion.
Bearings, shafts and joints
Bearing: equivalent dynamic load calculation
Calculate the equivalent dynamic bearing load P from radial and axial loads and the factors X and Y. Examples and model limitations.
Strength of materials and structural sizing
Bending stress: calculation using the section modulus
Calculate bending stress in a beam from the bending moment and section modulus. Examples in MPa, fiber selection and conversions.
Fluid mechanics
Bernoulli’s equation: calculate pressure between two points
Calculate an ideal fluid’s pressure between two points using velocities and elevations. Examples of elevation gain and contraction, without head losses.
Bearings, shafts and joints
Bolt: calculating tensile stress and proof load
Calculate the nominal tensile stress in a bolt and compare it with the proof load. Tensile stress area, total force, examples and limitations.
Bearings, shafts and joints
Bolt preload: calculation from proof load
Calculate a bolt’s target preload from tensile stress area, proof stress and the selected fraction. Examples and limitations, without tightening instructions.
Bearings, shafts and joints
Bolt tightening torque: calculation from preload
Estimate bolt tightening torque from the target preload, diameter and factor K. Examples, conversions and accuracy limitations.
Fluid mechanics
Buoyancy: calculation for an immersed body
Calculate buoyancy using immersed volume and fluid density. Examples, conversions to litres and limits of the flotation calculation.
Toolbox
Circle: calculate radius, circumference and area
Calculate the radius, diameter, circumference and area of a circle from a single measurement. Formulas, direct and inverse examples, rounding and units.
Fluid mechanics
Circular pipe: calculating flow rate and cross-sectional area
Calculate the cross-sectional area and volumetric flow rate of a full circular pipe from its inside diameter and mean velocity. Examples in mm and L/min.
Thermal engineering and heat transfer
Conduction through a pipe: calculating heat losses
Calculate thermal resistance and heat loss rate by conduction through a cylindrical wall using radii, length and thermal conductivity.
Toolbox
Constant-acceleration motion: calculating v, x and a
Calculate velocity, displacement or acceleration in uniformly accelerated rectilinear motion. Direct and inverse examples, signs and positive duration.
Fluid mechanics
Continuity equation: calculating velocity and flow rate
Calculate velocity in a second cross-section and the volumetric flow rate of an incompressible fluid. Contraction and expansion examples, limitations of the balance.
Machining and manufacturing
Cutting speed: calculating rotational speed and diameter
Convert between cutting speed, rotational speed in rpm and effective diameter in all three directions. Formula n = 1 000 × vc / (π × D), examples and limitations.
Toolbox
Dot product: calculating the angle between two vectors
Calculate the dot product, magnitudes and angle between two 2D or 3D vectors. Examples, coordinate-system conventions, unsigned angle and projection.
Fluid mechanics
Drag force: calculation from relative speed and area
Estimate drag force and the associated power from relative speed, density, reference area and drag coefficient. Examples.
Electrical engineering
Electrical cable: calculating cross-section from voltage drop
Estimate cable cross-section in mm² to meet a target voltage drop in single-phase or balanced three-phase circuits. Resistivity, examples and limitations.
Electrical engineering
Electricity consumption: energy and cost calculation
Estimate an appliance’s energy consumption in kWh and cost from its power, operating time and your tariff. Numerical examples and limitations of the balance.
Strength of materials and structural sizing
Euler buckling: calculating critical load
Calculate a bar’s critical buckling load, stress and slenderness from Young’s modulus, second moment of area, length and supports.
Strength of materials and structural sizing
Friction force: static and kinetic calculation
Calculate kinetic friction force and the static limit from the normal reaction. Examples on horizontal or inclined planes, sourced coefficients.
Power transmission and gears
Gear ratio: output speed calculation
Calculate the transmission ratio and output speed of two external gears. Driving and driven gears, reduction and direction of rotation.
Toolbox
Gravitational potential energy: calculation from height
Calculate gravitational potential energy, its change between two heights and the work done by gravity. Reference level, signed examples and a uniform field.
Fluid mechanics
Head loss: Darcy–Weisbach pipe calculation
Calculate distributed and local pipe losses as pressure and head. Supplied Darcy factor, local loss coefficients and elevation difference.
Thermal engineering and heat transfer
Heat conduction: calculation for a plane wall
Calculate the thermal resistance and heat transfer rate through a plane wall from conductivity, thickness, area and temperature difference. Model limitations.
Thermal engineering and heat transfer
Heat exchanger: calculating LMTD and surface area
Calculate LMTD, heat transfer rate or heat exchanger area with a known coefficient U. Parallel flow, counterflow, examples and limitations.
Strength of materials and structural sizing
Hooke’s law: calculating spring force
Calculate the force, stiffness or deflection of a linear spring with F = k × x. Worked examples, unloaded length and N/m and N/mm conversions.
Hydraulics, pneumatics and pressure
Hydraulic cylinder: calculating extension and retraction speeds
Calculate a cylinder’s ideal extension and retraction speeds from incoming flow rate and effective areas. Examples in mm/s and circuit-related limitations.
Hydraulics, pneumatics and pressure
Hydraulic cylinder: calculating push and pull forces
Calculate the ideal extension and retraction forces of a single-rod cylinder from pressure and full and annular areas. Examples and limitations.
Hydraulics, pneumatics and pressure
Hydraulic cylinder: stroke time calculation
Estimate the extension, retraction and round-trip times of a hydraulic cylinder from flow rate and geometry. Swept volumes and the actual machine cycle.
Fluid mechanics
Hydrostatic pressure: calculation from depth
Calculate the pressure increase in a fluid at rest with p = ρ g h. Depth, density, examples and relationship with absolute pressure.
Hydraulics, pneumatics and pressure
Ideal gas law: calculating P, V, n or T
Calculate absolute pressure, volume, amount of substance or temperature with PV = nRT. Four worked examples, conversions and limitations.
Electrical engineering
Induction motor: calculating speed, frequency and slip
Calculate an induction motor’s speed, frequency or slip from the number of poles. Examples, synchronous speed and kinematic limitations.
Toolbox
Kinetic energy: calculate energy, speed or mass
Calculate a body’s translational kinetic energy, speed or mass. Worked examples, unit conversions and the role of speed squared.
Thermal engineering and heat transfer
Latent heat: calculating the energy of a phase change
Calculate the energy absorbed or released during a phase change using Q = m × L. Signed examples, partial transformation and sensible heat.
Fluid mechanics
Mach number: calculation from speed and the speed of sound
Calculate the Mach number using speed and the speed of sound. Examples, speed of sound in air by temperature and regimes from subsonic to supersonic.
Machining and manufacturing
Machining time: calculation from feed rate
Calculate theoretical machining time per pass and in total from cutting length, linear feed rate and the number of identical passes.
Strength of materials and structural sizing
Mass–spring system: calculate the natural frequency
Calculate the natural frequency, angular frequency and period of a mass–spring oscillator. Examples, stiffness conversions and limits without damping.
Toolbox
Mechanical energy: calculation using energy conservation
Calculate a body’s kinetic, potential and mechanical energies, or its speed using conservation. Height reference and limitations of the loss-free model.
Power transmission and gears
Mechanical power: calculation from work or force
Calculate average power from work or instantaneous power of a force aligned with velocity. Transfer sign, units, average and peak.
Strength of materials and structural sizing
Metal density: table and mass calculation
Look up the density of common metals in kg/m³ and g/cm³, then calculate a mass or density. Sourced reference values and conversions.
Machining and manufacturing
Milling: calculating material removal rate and power
Calculate material removal rate, cutting power and input power from width, depth, feed rate, specific cutting force kc and efficiency.
Machining and manufacturing
Milling feed: calculate table feed and feed per tooth
Calculate a milling cutter’s table feed, feed per tooth, spindle speed or number of teeth. Formula, worked examples and calculation limits.
Power transmission and gears
Module and diametral pitch: gear conversion calculation
Convert a gear’s module to diametral pitch (DP) and vice versa: module in mm, teeth per inch of pitch diameter. Formula and examples.
Strength of materials and structural sizing
Moment of a force: calculation using the lever arm
Calculate the moment of a force and the lever arm, or find the force for a given moment. Perpendicular and oblique examples, planar model.
Toolbox
Momentum: calculating impulse along an axis
Calculate momentum and impulse using signed velocities, average force and duration. Rebound examples and limitations of the mechanical balance.
Thermal engineering and heat transfer
Multilayer wall: thermal resistance calculation
Calculate area-specific and total thermal resistance and heat transfer rate for three plane layers in series. Examples, an absent layer and temperature difference.
Electrical engineering
Ohm’s law: voltage, current, resistance and power
Calculate voltage, resistance or current with Ohm’s law. Additional power and energy results, unit conversions and zero cases explained.
Power transmission and gears
Open belt: calculating length from centre distance
Estimate the pitch length of an open belt from the pulley pitch diameters and their centre distance. Formula, examples and geometric limitations.
Thermal engineering and heat transfer
Overall heat transfer coefficient U: calculation for a plane wall with convection
Calculate the overall heat transfer coefficient U of a plane wall with two convection films. Thermal resistance per unit area, examples and coefficient selection.
Toolbox
Percentage: calculate the part, rate and change
Calculate a percentage, rate, total or relative change. Worked examples, choice of base, successive changes and percentage points.
Electrical engineering
Power factor: calculating reactive power compensation in kvar
Calculate power factor and the reactive power to compensate to reach a target cos φ. Inductive examples and limitations when choosing capacitors.
Hydraulics, pneumatics and pressure
Pressure, force and area: calculating p = F / A
Calculate pressure, normal force or area with p = F / A. Detailed examples, pressure and area conversions, limitations of the uniform model.
Hydraulics, pneumatics and pressure
Pressurized tube: hoop and axial stress calculation
Calculate hoop and axial stresses in a closed thin-walled tube from pressure, diameter and thickness. Examples and limitations.
Power transmission and gears
Pulley ratio: calculate speed and diameter
Calculate the ratio, driven speed or pitch diameter of a belt drive. Reduction and step-up examples, without slip.
Fluid mechanics
Pump: hydraulic power and shaft power calculation
Calculate a pump’s hydraulic power and shaft power from flow rate, pressure difference and efficiency. Examples, conversions and limitations.
Toolbox
Regular polygon: area and perimeter calculation
Calculate the area, perimeter, apothem, radius and angles of a convex regular polygon. Examples, units and the difference between apothem and radius.
Strength of materials and structural sizing
Resultant force: calculate components and magnitude in 2D
Add two to four forces in a plane and calculate the signed components and magnitude of the resultant. Angle conventions, examples and limits.
Fluid mechanics
Reynolds number: calculation and flow regime
Calculate the Reynolds number using dynamic or kinematic viscosity, then identify laminar, transitional or turbulent flow in a circular pipe.
Power transmission and gears
Rotational dynamics: torque and acceleration calculation
Calculate net torque, angular acceleration or moment of inertia about a fixed axis using C = J × α. Signed examples and model limitations.
Power transmission and gears
Rotational kinematics: calculations with constant angular acceleration
Calculate angular velocity, angular displacement or acceleration for rotation with constant acceleration. Examples with signed values and multiple revolutions.
Power transmission and gears
Rotational kinetic energy: calculation using the moment of inertia
Calculate rotational energy, angular velocity or moment of inertia using E = ½ J ω². Direct and inverse examples, and the difference from translation.
Toolbox
Rule of three: calculate the missing value
Find the fourth value in a direct proportion by cross multiplication. Price and recipe examples, consistent units and limits of proportionality.
Strength of materials and structural sizing
Section: calculate mass per unit length and weight
Calculate a section’s mass and weight using the steel catalogue, area and material, or kg/m. IPE, HE, UPN, angles and tubes, formulas and examples.
Strength of materials and structural sizing
Sections: calculate second moment of area and section modulus
Calculate Ix, Iy, section moduli, area and radii of gyration for 8 sections: rectangle, circle, tubes, I/H, U, T and L. Formulas and examples.
Thermal engineering and heat transfer
Sensible heat: calculating the energy for heating or cooling
Calculate the energy needed to heat or cool a mass without a phase change. Examples with signed values, temperature units and an energy balance before losses.
Bearings, shafts and joints
Shaft torsion: stress and angle calculation
Calculate shear stress, polar moment and angle of twist of a solid or hollow shaft. Examples, conversions and limits of the elastic model.
Bearings, shafts and joints
Shaft under torsion: calculate the minimum diameter
Calculate the theoretical diameter of a solid shaft subjected to torque using an allowable shear stress. Examples, units and limits of the stress-only criterion.
Electrical engineering
Single-phase power: calculate current and P, Q, S
Calculate current and active, reactive and apparent power in a sinusoidal single-phase circuit. Inductive and capacitive examples, model limitations.
Power transmission and gears
Spur gear: calculating tangential, radial and normal forces
Calculate tangential, radial and normal forces on a spur gear from torque, pitch diameter and pressure angle.
Power transmission and gears
Spur gears: calculating pitch diameters and centre distance
Calculate the pitch diameters and centre distance of two spur gears without profile shift from module and tooth counts. Examples and limitations.
Machining and manufacturing
Tap drill: diameter calculation and M1 to M48 table
Find the drilling diameter for metric tapping: D − p calculation and tables for coarse pitches M1–M48 and fine pitches M3–M48, with sources and limitations.
Machining and manufacturing
Tapping feed: calculation from pitch and spindle speed
Calculate the feed of a synchronized tap: thread pitch × spindle speed. Conversions between mm/min and m/min, worked examples and limits.
Thermal engineering and heat transfer
Thermal equilibrium: calculating the final temperature of two bodies
Calculate the equilibrium temperature of two isolated bodies from their masses and specific heat capacities. Examples and limitations without a phase change.
Thermal engineering and heat transfer
Thermal expansion: calculating the elongation of a bar
Calculate the elongation of a bar due to temperature: ΔL, final length and strain. Table of coefficients α, units and examples.
Electrical engineering
Three-phase motor: current calculation with efficiency and cos φ
Estimate the current drawn by a three-phase motor from useful output power, efficiency and cos φ. Loss balance, examples and starting current.
Electrical engineering
Three-phase power: calculating line current and P, Q, S
Calculate line current and total powers of a balanced sinusoidal three-phase system. Line-to-line voltage, examples and reactive power sign.
Power transmission and gears
Torque, power and rotational speed: calculation
Calculate torque, mechanical power or shaft rotational speed. Conversion from rpm to rad/s, examples and electrical power.
Electrical engineering
Transformer: calculating rated current and loading percentage
Calculate a transformer’s rated current and loading percentage from kVA rating, voltage and active power demand. Single-phase and three-phase examples.
Toolbox
Triangle: calculating sides, angles and area
Solve a triangle from three sides, two sides and the included angle (SAS), or two angles and one side. Area, perimeter and geometry checks.
Power transmission and gears
Uniform circular motion: calculate centripetal force
Calculate speed, centripetal acceleration and force in uniform circular motion. Conversions, examples and the effect of radius at a fixed frequency.
Toolbox
Vectors: calculating sum, magnitude and unit vector
Calculate the sum, difference, scalar multiple, magnitude and unit vector of 2D or 3D vectors. Ten examples explain signs, coordinate frames and limitations.
Electrical engineering
Voltage drop: calculation for single-phase and balanced three-phase circuits
Calculate the voltage drop in volts and percent for a single-phase or balanced three-phase line using current, length, R′, X′ and cos φ.
Toolbox
Volume: calculate a cuboid, cylinder, cone or sphere
Calculate the volume of a cuboid, cylinder, cone or sphere from its dimensions. Formulas, examples in litres, cm³ and m³, and choice of radius.
Strength of materials and structural sizing
Von Mises stress: equivalent stress calculation
Calculate the von Mises equivalent stress from normal and shear stresses. 2D and 3D formulas, worked examples and interpretation.
Toolbox
Work done by a force: calculation using displacement and angle
Calculate the signed work done by a constant force over a displacement. Driving, resisting or zero-work examples, cosine projection and energy-related limits.
No calculators match your search. Try another term or select all fields.
Guides and tables
Browse the guides →Choose the data, understand the assumptions and interpret the results.
- Checking a beam: from load to IPE selection
- Tapping: choose the right drill and avoid workshop errors
- Choose pipe diameter without guessing coefficients
- Bearings: find C and C₀, then interpret L10 correctly
- Pre-size a cylinder without overlooking the rod and mounting
- Tightening torque: find the right data before calculating