Skip to content
Formulaxis
Calculation guide / verifiable example

Checking a beam: from load to IPE selection

Two sections may satisfy strength requirements yet differ on the actual governing criterion: deflection.

Formulaxis · Documented technical demonstration · Revision: 15 November 2026

Short answer. A beam cannot be selected solely by bending stress. First establish load paths and supports, then check stress, deflection and stability for the same case. The lightest section does not always meet the displacement criterion.

The classic trap is to calculate σ = M/W, observe moderate stress and declare the beam suitable. Yet deflection may be excessive; an unbraced open section may also be susceptible to lateral-torsional buckling. This method therefore starts with a precise static model, then compares two IPE sections with properties from a manufacturer's catalogue.

1. Data to gather before calculation

InputHow to obtain itCommon error
Span and supportsDistance between support axes; identify pin/roller or actual fixed restraint.Treating a welded joint as perfectly fixed without evidence.
Service loadsSuspended mass, equipment, distributed load, self-weight; specify combinations.Omitting self-weight or fictitiously distributing a concentrated load.
I and WSection catalogue, same axis and orientation.Confusing cm⁴, mm⁴ and section modulus in cm³.
E and limitsMaterial at operating temperature; criteria from the project / applicable code.Using a universal deflection limit; L/500 is an exercise assumption here.
F = 12 kNL = 4 m · two supports · central forceAB
Original example diagram. It represents neither a distributed load nor a fixed connection.

2. Solve the problem in the correct order

1 Establish reactions and maximum moment

For a point force F halfway between two simple supports, each support carries F/2 and maximum moment is FL/4. If the load is offset, distributed or supports differ, this result no longer applies. The load sketch is a calculation deliverable, not decoration.

M_max = F × L / 4 = 12 000 × 4 / 4 = 12 kN·m
Statics · load diagramSupport AR = 6 kNMidpointM = 12 kN·mSupport BR = 6 kN
Example maximum moment · original Formulaxis diagram, values for this example only

2 Obtain I and W about the correct axis

For the strong axis, the ArcelorMittal catalogue gives IPE 160 : I = 869 cm⁴, W = 109 cm³ and IPE 200 : I = 1 940 cm⁴, W = 194 cm³. Retain the catalogue's y-y axes in the calculation report; physically rotating the beam may switch to a much smaller second moment of area.

See our IPE table extract with units and source.

Read about the same axisI in cm⁴For deflectionW in cm³For stressM about ySame axis as I, W
Two properties / two functions · original Formulaxis diagram, values for this example only

3 Check elastic stress

With M in N·mm and W in mm³, M/W gives MPa directly. In this case, the comparison limit of 140 MPa is a fictitious exercise criterion : it is neither a Eurocode limit nor a calculated structural resistance.

σ = |M| / W ; IPE 160 : 12 × 10⁶ / (109 × 10³) = 110.09 MPa
σmax — fictitious 140 MPa limitIPE 160110.09 MPaIPE 20061.86 MPaExercise limit: 140 MPa
Stress comparison · original Formulaxis diagram, values for this example only

4 Check deflection, then the checks not covered

This beam's central deflection is FL³/(48EI). It depends on the cube of the span : increasing span by 10 % already increases deflection by about 33 % if all else stays equal. L/500 (8 mm at 4 m) is selected for this exercise; a project may require another limit depending on use, finishes and vibrations.

δ = F × L³ / (48 × E × I) ; E = 210 000 N/mm² (assumption)
Central deflection — fictitious limit L/500 = 8 mmIPE 1608.77 mmIPE 2003.93 mmExercise limit: 8 mm
Deflection comparison · original Formulaxis diagram, values for this example only

3. Full example: why the lightest section fails

Teaching assumptions: F = 12 kN at midspan, L = 4 m, E = 210 GPa, comparison limit σ = 140 MPa, deflection limit L/500 = 8 mm. Idealized service load; self-weight is excluded from the deflection calculation below and must be added for a complete study.

Sectionσ (MPa)δ (mm)Mass over 4 mExercise conclusion
IPE 160110.098.7763.2 kgStress OK, deflection > 8 mm
IPE 20061.863.9389.6 kgBoth criteria met

Formulaxis calculations using ArcelorMittal properties; the finding applies only to this elastic bending case and the selected fictitious limits.

Interpretation: changing from IPE 160 to IPE 200 adds about 26.4 kg over 4 m but lowers deflection from 8.77 to 3.93 mm. Engineering requires explaining the governing criterion rather than arbitrarily declaring a “best” section.

Reproduce the calculation and vary the section

Change section, load or span: both criteria and mass are recalculated. Geometric properties remain those of the ArcelorMittal catalogue, strong axis.

110.09 MPaElastic stress
8.77 mmCentral deflection
63.2 kgTheoretical mass

4. Practical advice: what this model misses

Do not confuse strong axis with “a sufficiently strong beam”

An IPE section loaded about its weak axis may deflect far more under the same load. Always record orientation and draw manufacturer axes in the calculation report; “I = 1 940 cm⁴” without an axis is ambiguous.

Lateral-torsional buckling may govern before yielding

If the compression flange is not laterally restrained, the section may buckle laterally and twist. Neither σ = M/W nor δ = FL³/(48EI) verifies this instability. Bracing, unrestrained length and applicable structural-code rules require separate study.

A “perfect” beam case may hide an incorrect static model

A distributed load is sometimes too quickly replaced by a point force, or a real support assumed perfectly fixed. Draw a free-body diagram, check ∑F = 0 and ∑M = 0, then document every assumption. Engineers' discussions of modeling errors confirm the value of this initial check; they do not replace a standard.

Stopping condition: if supports, loading, lateral stability or actual material grade are unknown, conclude only with a preliminary elastic comparison.

5. From the method to Formulaxis

In practice, follow the tools in order: geometric properties → maximum moment → bending stress → deflection → mass. Enter your values into the calculators below, keeping the stated units and assumptions.

Reusable reference: IPE 160 to 220: I, W and mass per metre. Continue with checking cylinder-rod buckling to understand how an instability other than bending may govern a slender component.

Sources and data status

Numerical values are retained in this document even if URLs change. The tables are reconstructed selections with source attribution, not full copies of brochures. Formulaxis calculations and teaching assumptions are identified separately.

  1. ArcelorMittal — Orange Book, IPE propertiesIPE I, W, mass and axes; geometry source.
  2. Technical discussion — defining load-diagram assumptionsPractical experience on reactions, support conditions and load paths.

Sources consulted / results cross-checked on 15 November 2026. Data sheets and catalogues may be revised: check the current edition for a real project.