Skip to content
Formulaxis

Machining and manufacturing

Tapping feed: calculation from pitch and spindle speed

Calculate the synchronized axial feed of a tap for a single-start thread. The thread pitch and spindle speed determine the required linear speed, without automatically selecting cutting conditions.

Created on , Revised on v2.0

Method and validation

Synchronised tapping feed

Axial advance per revolution for a single-start thread, strictly positive.

Spindle speed, positive or zero; the direction of the machine cycle is not inferred.

Initial values are examples.

Results

Synchronised axial feed vf
0.75m/min

Single-start thread and ideal synchronisation; check the machine cycle and whether its feed is per minute or per revolution before transferring values.

Applied formulas

vf=p×n2×acos(−1)
vf=(0.0015 m)×(52.36 rads)2×acos(−1)=0.75 m/min

Values are substituted in SI units and results are shown in the selected units.

Estimated reading time : 6 min · 1125 words

Calculation details

The steps below use the inputs and units selected in the calculator. Workshop units: vf [mm/min] = p [mm] × n [rpm]; inverse n=vf/p. The inferred speed checks synchronization only; it does not select a suitable cutting speed. Pitch remains a known property of a single-start thread. Synchronization applies to cutting and forming taps; their drill sizes, torques and cutting speeds differ. Rigid tapping requires control-synchronized spindle and axis motion; a compensating holder requires its own procedure.

01 · Synchronized axial feed

FORMULA

vf=p×n2×acos(−1)

NUMERICAL SUBSTITUTION

vf=(1.5 mm)×(500 rpm)2×acos(−1)

RESULT

vf=0.75 m/min

Feed and spindle synchronization

When tapping a single-start thread, the tool advances one pitch per revolution. The axial feed speed must therefore equal the product of pitch and rotational frequency. The calculation gives a magnitude; direction depends on the thread hand and direction of rotation.

Formulas and symbols

Choose feed or spindle speed as the unknown. Both modes require the known pitch of a single-start thread. Then enter the known speed or feed; 0.75 m/min equals 750 mm/min.

vf=p×n2×acos(−1)

n=2×acos(−1)×vfp

  • p: pitch of the single-start thread, default displayed unit: mm.
  • ω: spindle speed, default displayed unit: tr/min.
  • vᶠ: synchronized axial feed, default displayed unit: m/min.

Guidance for interpreting results

Quantity or conditionInterpretation
Single startAxial feed per revolution equals the pitch
Multiple startsFeed per revolution is the lead, outside the model of this page
Tap withdrawalAdjust direction and synchronization according to the machine
Pitch and speedvᶠ [mm/min] = p [mm] × n [rpm]
Feed conversion1 m/min=1 000 mm/min
Inch threadp=25.4 / number of threads per inch, in millimetres
Spindle speedChoose according to the tap’s cutting speed; it then determines the feed
Feed per revolution different from the pitchDamaged thread and excessive axial load on the tap

Sandvik Coromant — Threading Formulas and Definitions ; NIST — SI prefixes.

ISO coarse metric thread pitches and feed at 500 rpm

ThreadPitch and synchronized feed at 500 rpm
M30.5 mm : 250 mm/min
M40.7 mm : 350 mm/min
M50.8 mm : 400 mm/min
M61 mm : 500 mm/min
M81.25 mm : 625 mm/min
M101.5 mm : 750 mm/min
M121.75 mm : 875 mm/min
M162 mm : 1 000 mm/min

Conversion of inch threads (UNC) to metric pitch

ThreadEquivalent pitch (25.4 / threads per inch)
1/4-20 UNC1.27 mm
5/16-18 UNC1.41 mm
3/8-16 UNC1.59 mm
1/2-13 UNC1.95 mm
5/8-11 UNC2.31 mm
3/4-10 UNC2.54 mm

Worked examples

Example 1: Pitch of 1,5 mm at 500 tr/min

The axial feed rate is 750 mm/min.

Example 2: Pitch of 1 mm at 800 tr/min

The axial feed rate is 800 mm/min.

Example 3: Checking conversion to m/min

This exercise uses a pitch in millimetres and explicitly checks feed conversion. The values illustrate synchronization; they are not a speed recommendation for an actual tool.

p=1.25 mm, n=300 rpm: vf=1.25×300=375 mm/min=0.375 m/min.

Example 4: M8 coarse thread (1.25 mm pitch) at 300 rpm

The standard coarse pitch of an M8 thread is 1.25 mm. The synchronized feed is 1.25×300=375 mm/min, or 0.375 m/min: the tap advances by 1.25 mm per spindle revolution.

Example 5: 1/4-20 UNC thread (1.27 mm pitch) at 600 rpm

A 1/4-20 UNC thread has 20 threads per inch, so p=25.4/20=1.27 mm. The synchronized feed is 1.27×600=762 mm/min, or 0.762 m/min.

Example 6: M8 at a cutting speed of 10 m/min

At a cutting speed of 10 m/min (an example value, to be replaced by the tap manufacturer’s value), n=1 000×10/(π×8)≈398 rpm. The feed is then 1.25×398≈497.5 mm/min, or approximately 0.50 m/min.

Assumptions and limitations

Single-start thread, ideal synchronization. No calculation of torque, pilot-hole diameter or machine parameters, no automatic TPI conversion and no multi-start threads.

Common mistakes

Using mm/dent; confusing pitch with feed per minute; omitting the number of starts for a multi-start thread.

Frequently asked questions

Must the nominal tap diameter be entered?

No. The feed relationship depends on pitch and speed, not nominal diameter.

Does the calculation replace setting up a tapping cycle?

No. The conventions, accelerations, reversals and cycle limits must be checked for the control and tool used.

Should feed be programmed per minute or per revolution?

This depends on the control and selected cycle. For feed per minute, use pitch multiplied by spindle speed in the required units. For feed per revolution, the value equals the pitch of a single-start thread. Check the machine manual before entering it.

Why are multiple-start threads excluded?

For a multiple-start thread, axial travel per revolution equals pitch multiplied by the number of starts. This page’s input represents the pitch of a single-start thread. Entering only the axial pitch would therefore underestimate the required travel.

How do you find the pitch of a metric or inch thread?

For a coarse metric thread, the pitch follows from the designation: M8 corresponds to 1.25 mm and M10 to 1.5 mm (see the table). For an inch thread, divide 25.4 by the number of threads per inch: 1/4-20 gives 1.27 mm. Then enter this pitch in millimetres.

What spindle speed should you choose for tapping?

Use the tap manufacturer’s cutting speed for the material and actual conditions, then n=1 000 × vc/(π×D), with vc in m/min and D in mm. Observe spindle, tool and cycle limits; no universal speed range is supplied.

What should you program in the control: mm/min or mm/rev?

This depends on the control and the cycle. In feed per minute mode, program the value calculated here (pitch × spindle speed); in feed per revolution mode, the programmed feed is generally equal to the pitch itself. Check your machine’s convention, and with a compensating tapping holder, follow its manufacturer’s recommendation.

How does the formula change for a multi-start thread?

The tool advances by one lead per revolution, equal to the pitch multiplied by the number of starts, and the relation becomes vᶠ = lead × n. This case is not covered by this page, whose field corresponds to the pitch of a single-start thread: do not enter the pitch alone for a multi-start thread.