Skip to content
Formulaxis
Selection guide and limitations

Bearings: find C and C₀, then interpret L10 correctly

A manufacturer's data sheet provides ratings; actual machine loading determines whether the choice is suitable.

Formulaxis · Documented technical demonstration · Revision: 15 November 2026

Short answer. Use the bearing designation to find the manufacturer's ratings C and C₀, then use actual loads to evaluate P, L10 and the static ratio. L10 is not a service-life guarantee : it is a statistical reference life associated with 90 % reliability for a group of bearings under defined conditions.

Our example starts with an identifiable product: SKF 6206-RZ (deep-groove ball bearing). The manufacturer publishes 30 × 62 × 16 mm, C = 20.3 kN and C₀ = 11.2 kN. We then choose purely radial loading to avoid inventing X and Y factors. This case does not automatically make the bearing suitable for a given machine.

1. Read the SKF data sheet correctly

Radial load FrSKF 6206-RZ30 × 62 × 16 mmC = 20.3 kN · C₀ = 11.2 kN
Original deep-groove ball bearing diagram showing radial load Fr. C and C₀ are not operating loads.
SKF data-sheet fieldValueIn Formulaxis
Product reference6206-RZIdentify the appropriate family, clearance and sealing
d × D × B30 × 62 × 16 mmShaft / housing compatibility (not checked here)
Basic dynamic load ratingC = 20.3 kNL10 calculation input
Basic static load ratingC₀ = 11.2 kNStatic safety factor input
Factors X, Y / X₀, Y₀Depend on the caseDo not infer from C alone

SKF values for the identified variant. Reread the data sheet for another bearing or product revision.

We retain a data and units sheet to keep these values available if the manufacturer's link changes.

2. From machine loading to bearing selection

1 Determine bearing forces

Start with shaft forces (weight, belt, gears, machining forces), then calculate reactions at each support. A bearing's transmitted force is not automatically the sum of all system forces: positions matter. Document radial and axial components, speeds and shocks separately.

Calculate reactions before entering PMachineForces and positionsSupport ARadial / axial loadSupport BRadial / axial load
From mechanism to Fr, Fa · original Formulaxis diagram, values for this example only

2 Determine P from the catalogue

For loading that is purely radial on our reference bearing, we use P = Fr, Fa = 0 here. As soon as axial load is present, apply the manufacturer's factors and any piecewise conditions; choosing X = 1, Y = 0 “because it is simple” may give an incorrect result.

Purely radial case: P = Fr = 4.0 kN (operating assumption)
Do not confuse catalogue data with loadsC20.3 kN · catalogueC₀11.2 kN · catalogueP4.0 kN · scenario
Rating and load · original Formulaxis diagram, values for this example only

3 Calculate L10 and convert it to hours

For ball bearings at constant load and speed, L10 = (C/P)³ million revolutions. With n = 1 200 rpm, revolutions are converted to hours. Increasing from 4 to 6 kN multiplies load by 1.5 and divides L10 life by 3.375 : the cubic relationship radically changes the conclusion.

L10h = (10⁶ / 60n) × (C/P)³
L10 for two loads at 1 200 rpmP = 4 kN1815 hP = 6 kN538 h
Effect on life · original Formulaxis diagram, values for this example only

4 Also check static load and mounting conditions

For this example's purely radial load, we use P₀ = Fr and s₀ = C₀/P₀ = 11.2/4 = 2.8. This ratio is not a compliance verdict. A nearly stationary bearing exposed to shock, mounting defects or permanent deformation may need a stricter static check than its L10 life suggests.

Separate check from fatigueP₀4 kN, radialC₀11.2 kN, SKFs₀2.8 · no verdict
Static check · original Formulaxis diagram, values for this example only

3. Numerical example: the intermittent-load trap

For the same SKF 6206-RZ at 1 200 rpm and Fa = 0, our fictional study considers a constant radial force of 4 kN, then 6 kN. C and C₀ are published ratings; the loads and speed belong to our exercise.

CaseLoad PL10 in hoursWhat this shows
Steady load A4 kN1 815 hComparison baseline
Steady load B6 kN538 hAdditional load has a strong impact
50 % of revolutions at 2 kN, 50 % at 6 kNP_eq ≈ 4.82 kN1 037 hDirectly averaging 2 and 6 kN would be misleading

For the cyclic example, weighting is by revolutions with exponent p = 3 and equivalent P = (Σ fractionᵢ × Pᵢ³)^(1/3). A two-state teaching example; it does not replace a real load spectrum or modified life.

P_eq = (0.5 × 2³ + 0.5 × 6³)^(1/3) ≈ 4.82 kN

See how load affects L10 life

SKF 6206-RZ: C = 20.3 kN, C₀ = 11.2 kN; radial load only, constant speed. No modified-life factors.

1 815 hBasic L10 life
2.80C₀/P₀ ratio, no universal threshold

4. Advice a simple L10 calculation cannot provide

Do not select a bearing by C alone

Also document shaft/housing fits, internal clearance, alignment, speed, lubrication, seals, temperature and mounting method. SKF notes that bearing selection is a comprehensive process and that a bearing with excellent rating life may be unsuitable for its actual environment.

Load peaks matter more than the arithmetic average

The P³ relationship makes high loads particularly influential. For a duty cycle, a simple average load cannot always be entered; a spectrum, the revolutions associated with each state and the correct equivalence model are needed.

For a slow or stationary shaft, the static check may govern

An indexing mechanism, stationary impacts or intermittent forces may require contact-deformation analysis, not only millions of revolutions. Do not display “safety verified” based solely on a calculated s₀.

No universal L10 or s₀ threshold is provided here. Reliability, availability and maintenance requirements are equipment-specific.

5. Continue with Formulaxis calculators

Manufacturer data: 6206-RZ data sheet, C/C₀ ratings, dimensions and interpretation conditions. Beam and transmission guides can supply initial reactions for calculating support forces, but load conventions must remain consistent.

Sources and data status

Numerical values are retained in this document even if URLs change. The tables are reconstructed selections with source attribution, not full copies of brochures. Formulaxis calculations and teaching assumptions are identified separately.

  1. SKF — 6206-RZ product data sheet30 × 62 × 16 mm ; C = 20.3 kN ; C₀ = 11.2 kN.
  2. SKF — bearing selection processSelection criteria beyond L10 life.
  3. SKF — Bearing rating life / fatigue modelLimits of equivalent load and L10 assessment.

Sources consulted / results cross-checked on 15 November 2026. Data sheets and catalogues may be revised: check the current edition for a real project.